Mk-diamond MK-170 Bedienungsanleitung

04.2011MK-170 TILE SAW OWNER'S MANUALPARTS LIST &OPERATING INSTRUCTIONSwww.mkdiamond.comCaution: Read all safety and operating instructions b

10Use of under sized extension cords result in low voltage to the motor that can result in motor burnout and premature failure. MK Diamond warns that

11OPERATION & SAFETY DECALSThe MK-170 Tile Saw is equipped with a number of safety decals. These decals are provided for operator safety and maint

12PRODUCT SPECIFICATIONSGENERAL DSCRIPTIONMOTOR SPECIFIFCATIONSBLADE CAPACITYTILE TYPESThe MK-170 is a versatile Tile Saw. Operated and used according

13MK-170 TILE SAW CONTENTSCONTENTS03.2011MK-170 TILE SAW OWNERS MANU

14MK-170 TILE SAW ASSEMBLYFollow the assembly instructions to prepa

15MK-170 TILE SAW ASSEMBLYWhen installing the Adjustable Cutting Gui

16Splash Guard InstallationPre-start Inspection(A)Install the Thumbscrew through the Washer and Splash guard then align to the hole found on the hole

17Water Pump Preparation(A)Install Water Pump Discharge Fitting(D)Fill the Water Pan with clean water (this should be done peri-odically during cuttin

18MK-170 TILE SAW OPERATIONMK-170 Setup for OperationCutting Tile1.

19MK-170 TILE SAW OPERATIONAdjustable Cutting Guide AlignmentIf durin

2INTRODUCTION Congratulations on your purchase of a MK-170 Tile Saw. We are certain that you will be pleased with your purchase. MK-170 Tile Saw ta

20CleanupDispose of wastewater in accordance with applicable Federal, State and Local laws.Ensure the saw is disconnected before completing the remain

21To extend the life of the MK-170, lubricate the Motor Shaft with light oils such as, 3 in 1, WD-40, etc.NOTE:MK-170 TILE SAW

22MK-170 TILE SAW MAINTENANCEBlade DressingLike most cutting instruments, a

23MK-170 TILE SAW MAINTENANCEMotor Brush Change-outDisconnect the tool befo

24MK-170 TILE SAW TROUBLESHOOTINGBlade will not cut properlyCooling Flow(A)Check for

25MK-170 TILE SAW TROUBLESHOOTINGBlade Stops Turning(D)Remove the Blade Guard In-take

26MK-170 TILE SAW TROUBLESHOOTING(D)Verify the circuit breaker is at least 20 amps -

27NOTES

28MK-170 TILE SAW EXPLODED VIEW

29MK-170 TILE SAW PARTS LISTItem Description Qty Part # A Accessor

3TABLE OF CONTENTS SAFETYSafety Messages 4 Damage Prevention Message 4 General Safety Precautions and Hazard Symbols 4 California Proposition 65 M

30Item Description Qty Part # K Table, 170 -- -- K1 Table, 170 1 157253 K2 Screw, 10-24 x 1/2 Pan Head Phillips Machine 4 151744 L

31MK-170 TILE SAW THEORYTHEORY OF DIAMOND BLADESDiamond blades

32ORDERING INFORMATIONYou may order MK Diamond products through your local MK Diamond distributor or, you may order direct from MK Diamond.NOTE: Ther

33NOTES

34NOTES

35NOTES

MK Diamond Products, Inc.1315 Storm ParkwayTorrance, CA 90501Toll-Free: (800) 421-5830Phone: (310) 539-5221Fax: (310) 539-5158www.mkdiamond.comMK-170

4Read and follow all safety, operating and maintenance instructions. Failure to read and follow these instructions could result in injury or death to

5If using an extension cord make sure it is in good condition first. When using an extension cord, be sure to use one heavy enough to carry the curren

6Consult the owner’s manual for recommended accessories. Using improper accessories may increase the risk of personal or by-stander injury. Serious i

7Sawing, grinding and drilling generates dust. Excessive airborne particles may cause irritation to eyes, skin and respiratory tract. To avoid breat

8ELECTRICAL REQUIREMENTS AND GROUNDING INSTRUCTIONSIn order to prevent potential electrical shock and injury, the following electrical safety precauti

9 Supporting Surface Power Tool Drip Loop Power Cord Drip Loop InformationTo avoid the possibility of the appliance plug or receptacle gettin